Get 156-835 Braindumps & 156-835 Real Exam Questions
CheckPoint 156-835 Actual Questions and Braindumps
The Check Point Certified Maestro Expert certification exam is a valuable credential for IT professionals who want to advance their careers in the field of cybersecurity. It demonstrates their expertise in managing complex security infrastructures and their ability to use Check Point Maestro to provide a unified view of the entire security infrastructure. Check Point Certified Maestro Expert certification is recognized globally and is highly regarded by employers in the IT industry.
CheckPoint 156-835 exam consists of 90 multiple-choice questions that need to be answered within 90 minutes. 156-835 exam is available in English and Japanese and can be taken at any Pearson VUE testing center. The passing score for the exam is 70%, and candidates who pass the exam receive the Check Point Certified Maestro Expert certification.
NEW QUESTION # 35
Which setting is required in order to connect an appliance with 40Gbps downlink interface and DAC to the Orchestrator MHO-140?
- A. On Orchestrator: Change QSFP mode from 100Gbps to 40Gbps
- B. No change required
- C. On Orchestrator: Change port type from uplink to downlink
- D. On Appliance: Change a port speed to 10Gbps
Answer: C
NEW QUESTION # 36
What is the default range of physical ports for downlinks on Orchestrator MHO-170?
- A. 1 - 16
- B. 25 - 32
- C. 3 - 16
- D. 17 - 31
Answer: D
NEW QUESTION # 37
What is the purpose of g_tcpdump command?
- A. Collects traffic dump from Sync network
- B. Collects traffic dump from CIN network
- C. Collects traffic dump from all Active Appliances within Security Group
- D. The same as tcpdump, just on Scalable Platform
Answer: C
NEW QUESTION # 38
What is the maximum amount of Appliances within Security group in Dual-Site configuration?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION # 39
What will happen in case of NAT of the traffic passing through Management network?
- A. This traffic will pass with no inspection
- B. Since Management traffic is always going to SMO, it will take a care for Correction Layer and will re-distribute traffic to other Appliances
- C. Orchestrator will disable NAT and traffic will pass with no issue
- D. This traffic will not pass correction, since it will be dropped
Answer: D
NEW QUESTION # 40
What is the difference between Dual-Site and Multi-Room?
- A. Multi-Room is Active / Standby and Dual-Site is Active / Active
- B. This is the same
- C. Multi-Room is a kind of Dual-Site deployment within the same building
- D. Multi-Room is a Single-Site deployment where all Appliances are connected to both orchestrators
Answer: C
NEW QUESTION # 41
What is the default IP range of Sync network (with no increment)?
- A. 192.168.1.0
- B. 192.0.2.0
- C. The same as Management network
- D. 198.51.100.0
Answer: B
NEW QUESTION # 42
What kinds of transceivers are supported on Orchestrator MHO-140?
- A. SFP, QSFP, QSFP28
- B. SFP, SFP+, SFP28
- C. SFP+, SFP28, QSFP
- D. SFP, SFP+, QSFP, QSFP28
Answer: D
NEW QUESTION # 43
What is the throughput penalty of Security Group?
- A. Depends on the type of Appliance
- B. 5% per member
- C. 10% per Security Group with no relation to amount of members
- D. 1% per member
Answer: A
NEW QUESTION # 44
There are two 10Gbps dual-port NIC installed on a 6800 appliance. Which interfaces should be connected to Orchestrator 1 for downlinks' intra-orchestrator redundancy when using two Orchestrators?
- A. Port 1 in Slot 1 and Port 1 in Slot 2
- B. Port 1 in Slot 1 and Port 2 in Slot 1
- C. Any pair of available ports
- D. Port 1 in Slot 2 and Port 2 in Slot 1
Answer: A
NEW QUESTION # 45
What is the Sync network on Appliances used for?
- A. To synchronize configurations and connections in between connection tables of different Appliances
- B. May be used for any purpose, but synchronization always have priority
- C. To transfer configuration files from Orchestrators to Appliances
- D. To transfer data in case of full utilization of the downlink interfaces
Answer: A
NEW QUESTION # 46
There are two 10Gbps dual-port NICs and one 40Gbps NIC installed on a 23800 Appliance in slots 1, 2 and 3 accordingly. Which interfaces should be connected to Orchestrator 1 for downlinks' intra-orchestrator redundancy when using two Orchestrators?
- A. Port 1 in Slot 1 and Port 2 in Slot 1
- B. This configuration is not supported
- C. Any pair of available ports
- D. Port 1 in Slot 2 and Port 2 in Slot 1
Answer: A
NEW QUESTION # 47
What cannot be learned from the output of asg monitor command?
- A. Security Policy status
- B. Uptime
- C. Appliances cluster status
- D. Port status
Answer: D
NEW QUESTION # 48
What is an uplink interface used for?
- A. To connect Orchestrators to customer's infrastructure
- B. To connect in between appliances
- C. To connect in between Orchestrators
- D. To connect appliances to customer's infrastructure
Answer: D
NEW QUESTION # 49
What is the default IP range of CIN network (with no increment)?
- A. 192.168.1.0
- B. 192. 0 .2 .0
- C. The same as Management network
- D. 198 .51 .100. 0
Answer: D
NEW QUESTION # 50
What is the Iterator process?
- A. Iterator is the process that follow Appliance recovery and simulates what was a distribution if recovered Appliance was alive
- B. Iterator is the process that simulates distribution in case of Appliance failure
- C. Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance failure
- D. Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance recovery
Answer: C
NEW QUESTION # 51
What command will be used for updating fwkern.conf file on all Appliances within Security Group?
- A. g_all update_conf_file
- B. g_update_conf_file
- C. vi
- D. g_update_kernel
Answer: A
NEW QUESTION # 52
What is a Security Group?
- A. Group of security administrators
- B. Group of appliances with enabled NGTX software blades
- C. Group of security gateways
- D. Logical group of computer and network resources
Answer: C
NEW QUESTION # 53
One single Appliance supports 1M concurrent connections. How many concurrent connections will support Security Group of 2 Appliances?
- A. 500K
- B. 1M
- C. 4M
- D. 2M
Answer: D
Explanation:
One single Appliance supports 1M concurrent connections, so a Security Group of 2 Appliances will support 2M concurrent connections.
https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails=&solutionid=sk91380 How to troubleshoot Gaia Portal (WebUI)
https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails=&solutionid=sk91380
https://downloads.checkpoint.com/dc/download.htm?ID=103853
VSX R81 Administration Guide
https://downloads.checkpoint.com/dc/download.htm?ID=103853
https://sc1.checkpoint.com/documents/Jumbo_HFA/R81.10/R81.10/R81.10-List-of-all-Resolved-Issues.htm List of All Resolved Issues and New Features
https://sc1.checkpoint.com/documents/Jumbo_HFA/R81.10/R81.10/R81.10-List-of-all-Resolved-Issues.htm
NEW QUESTION # 54
What kinds of transceivers are supported on Orchestrator MHO-170?
- A. SFP. SFP+. SFP28
- B. SFP+, SFP28. QSFP
- C. SFP. QSFP, QSFP28
- D. QSFP. QSFP28
Answer: D
NEW QUESTION # 55
What is the minimal requirement for a Security Group?
- A. 1 Appliance and 1 management port
- B. 2 Appliances and 2 ports
- C. 1 Appliance and 1 administrator with Multi-Domain admin permissions
- D. None, it may be empty.
Answer: A
NEW QUESTION # 56
When running asg perf -v in a Dual-Site environment, we can see only Appliances from one of the sites. That means we're working in:
- A. Active / Standby HA mode
- B. Active /Active
- C. This is not Dual-Site, in Dual-Site we always see Appliances from both sites
- D. VSLS mode
Answer: A
NEW QUESTION # 57
What does the command'g_all' do?
- A. Bring up all Appliances
- B. It's followed by other command and execute it on all Appliances connected to Orchestrator
- C. It's followed by other command and execute it on all active Appliances within Security Group
- D. Switches all Appliances to Global mode
Answer: C
NEW QUESTION # 58
How many power supplies are presented on MHO-170?
- A. 1 with option for 2
- B. 0
- C. 1
- D. 2
Answer: B
NEW QUESTION # 59
What is the purpose of Management ports located on the Rear Panel of the Orchestrator MHO-140?
- A. 1Gbps connectivity for Security Groups.
- B. Out-of-band interfaces for access to Orchestrator itself.
- C. Reserved for internal purposes. Not in use.
- D. Additional ports used as uplinks.
Answer: B
NEW QUESTION # 60
......
156-835 Dumps To Pass CheckPoint Exam in 24 Hours - BraindumpsPrep: https://passleader.briandumpsprep.com/156-835-prep-exam-braindumps.html
